Header

ASTM F1554 Specification

ASTM F1544 is a standard material specification for straight, bent, headed, headless anchor bolts and all-thread anchor rods, made of carbon, medium carbon boron, alloy, or high-strength low alloy steel. ASTM F1554 covers anchors bolts in grade 36, 55 and 105, each designated with minimum ksi strength value. These anchors bolts or anchor rods are intended for anchoring structural supports to concrete foundations. Such structural supports include building columns, column supports for highway signs, street lighting and traffic signals, steel bearing plates, and similar applications.

Supplementary requirements are included to provide for grade 55 weldable steel, permanent manufacturers and grade identification marking, and impact properties for grade 55 and 105.

Grade Classification

Type Descriptions Tensile Strength, ksi (MPa) Yield Strength, min, ksi (MPa) Diameter, Range, Inch.
Grade 36 Low carbon, 36 ksi yield steel anchor bolts 58 - 80 (400 - 558) 36 (248) 1/2 - 4
Grade 55 High strength, low alloy, 55 ksi yield steel anchor bolts 75 - 95 (517 - 665) 55 (380) 1/2 - 4
Grade 105 Alloy, heat treated, high strength 105 ksi yield steel anchor bolts 125 - 150 (862 - 1034) 105 (724) 1/2 - 3

Chemical Composition


Element		 Composition, %
Grade 36 Grades 55 and 105
Diameter up-to 3/4" Inclusive Over 7/8" to 4" Inclusive All Diameters

Carbon, max		 Heat 0.25 0.25 -
Product 0.28 0.28 -

Manganese		 Heat - 0.60 - 0.90 -
Product - 0.54 - 0.98 -

Phosphorus, max		 Heat 0.04 0.04 0.04
Product 0.05 0.05 0.048

Sulfur, max		 Heat 0.05 0.05 0.05
Product 0.06 0.06 0.058
Copper, min
(when specified)		 Heat 0.20 0.20 0.20
Product 0.18 0.18 0.18

Mechanical Properties [Bar & Machined Specimen]

Property Grade 36 Grade 55 Grade 105
Tensile Strength, ksi 58 - 80 75 - 95 125 - 150
Yield Strength, min, ksi (0.2% Offset) 36 55 105
Elongation in 8 inch, min, % [Note A] 20 18 12
Elongation in 2 inch, min, % [Note A] 23 21 15
Reduction of Area, min, % 40 30 45
Note A:

Elongation in 8 Inch applies to bars. Elongation in 2 inch applies to machined specimens.

Protective Coatings

  • Zinc, Hot Dip or Mechanically Deposited:
  • When zinc-coated anchor bolts are required, the purchaser shall specify the coating process, for example, hot dip, mechanically deposited, or no preference. When no preference is specified, the supplier may furnish bolts coated with either process. The supplier’s option is limited to one process per item, with no mixed processes in a lot.
  • When hot-dip zinc coated anchor bolts are specified, the anchor bolts and nuts shall be zinc-coated in accordance with the requirements of Specification F2329/F2329M.
  • When mechanically deposited zinc coated anchor bolts are provided, the anchor bolts and nuts shall be zinccoated in accordance with the requirements of Specification B695, Class 55.
  • Unless otherwise specified, when zinc-coated washers are required, the washers shall be hot-dip zinc-coated in accordance with Specification F2329/F2329M, or mechanically deposited zinc coated in accordance with Specification B695, Class 55. The coating process for the washers need not be the same as that for the anchor bolts and nuts.
  • Other Coatings:
  • When indicated on the inquiry and purchase order, coatings other than those in 7.1 shall be as agreed upon by the purchaser and supplier.

Recommended Nuts & Washers


Anchor Bolts		 Recommended A563 Nuts
Plain Finish Hot-Dip or Mechanical Zinc Coated
Bolt Grade Diameter, Inch Grade Style Grade Style
Grade 36 1/2 - 1 1/2 A Hex A Hex
Over 1-1/2 A Heavy Hex A Heavy Hex
Grade 55 1/2 - 1 1/2 A Hex A Heavy Hex
Over 1-1/2 - 4 A Heavy Hex A Heavy Hex
Grade 105 All DH Heavy Hex DH Heavy Hex

Reference Standards

Footer